This makes the unit fully self-contained, so you won't have to locate the temp sensor yourself, saves time! This CBT7 Control comes with 5kw 15" high flow heater, 2.5x5.0" Topside display/keypad, pump and blower and light cords, and is a complete unit to replace your old spa control and heater. Topside drops into a 1-3/4 round cutout in your spa. Intended for use under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. Runs a main 2 speed spa pump, and an air blower or 2nd pump, and spa light, and has a receptacle for ozonator or ionizer or any other non-switched device.
Comes with new power cords for your main 2-speed pump and an air blower or second pump, and a light, with quick disconnect plugs to the control. Temperature sensor comes with a long cord so you can either mount the sensor onto the heater, or, mount it in your tub if your tub has a drywell, has provision for a remote temp sensor. Cord is 8 feet long, but again it is your choice to mount it right on the heater or stick the sensor into a tub fitting you already have. Includes 15 inch long stainless steel high flow 2 heater, with 5kw Incoloy element.
Can be used on 115/120v or 230/240 volts, it's changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The CBT7 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115/120v or 230/240v. On a 115/120 volt source, the heater will be 1.25kw or 1250 watts.
From the factory the CBT7 is set for 230/240v incoming power, 230/240v to the heater, and 230/240v to the pumps. 115/120v to the air blower, and the ozonator, and 12 volts to the light. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2" or 2" PVC pipe size systems.
User's Manual shows how to program changes into the control, but it is factory programmed, and tested by United, and ready to go as is. Control box stands 11.1" tall, and 15.5" wide, 3.4" deep, heater is 15" flange to flange. Designed, built and tested in the U. By United Spas, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by United Spas.United has been building digital hot tub controls over 20 years. CBT7 Digital Control by United Spas model C5. 15" stainless steel high flow 5kW heater with standard threaded couplings for 2" PVC plumbing.
Digital display keypad (topside) 2.5x5.0 with 9.5 foot long cord. Drops into 1-3/4 round cutout. One pump power cord 4-wire for a 2-speed pump, 45 long with quick disconnect AMP plug and motor connectors. Air Blower power cord 57 with quick disconnect AMP plug, 18/3 wire size.
Light cord with quick disconnect AMP plug, 8 foot long. United Spas t& Topside Installation Manual & User's Guide.United Spas C5 Series Installation & Service Manual. Additional info: Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware.
The item "Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 5 cords" is in sale since Tuesday, January 02, 2018. This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs". The seller is "distributors-fulfillment" and is located in Los Angeles, California.
This item can be shipped to United States.